How To Change The Jaw Carrier On A Coats 5060 E

1. Coats Tire Machine Accessories
2. How To Change The Jaw Carrier On A Coats 5060 Ebay
3. Coats 7050ax

Replacement wheel clamping jaw for many Coats rim clamp tire changers with adjustable jaws. Price is for a single jaw. It is recommended to replace all 4 jaws at the same time for even clamping.

Coats Tire Machine Accessories

Motor Carrier PermitThe Motor Carrier Permit (MCP) is issued by the California Department of Motor Vehicles (DMV). Following is a brief overview of MCP requirements.

How To Change The Jaw Carrier On A Coats 5060 Ebay

• Tire Changer. For servicing single piece automotive and most light truck. Manufacturer of AMMCO®, COATS® and BADA® Automotive Service Equipment and Tools. Carrier/Cover - Cylinder End. Plastic Clamp Jaw. 14-15 SCFM at 150 PSI. 14-15 SCFM at 150 PSI.
• Amazon.com: coats tire changer parts. Tire Machine Changer Table Cylinder Seal Kit Fits Coats. Model 5060 5030 5070 replaces #8183811. Quilted Clamp Sock For Rim Clamp Jaw For Coats Tire Changers. 5.0 out of 5 stars 1. FREE Shipping by Amazon. Only 9 left in stock - order soon.

Always Disconnect Air Supply Before Attempting this installation! On 5050/5060E Models, Disconnect Electric Power Supply!1. Read and review instructions becoming familiar with parts, dis-assembly, and reassembly procedure before proceeding!2. Remove and discard (4) 3/8' nylon tubes connecting spider and clamp carriers.

Note on some models discard tube protectors (springs) if present.3. Remove (2) 1/2-13 hex nuts holding table top air cylinder to clamp carriers. Do not discard these as they will be used later to re-connect carriers to cylinder.4. Remove (4) 12mm X 2 5/8' hex head shoulder bolts holding link bar to clamp carrier and clamp.

Coats 7050ax

Then remove and discard clamp carriers, clamps and shoulder bolts.5. Attach new clamp carriers (2) 3182248 (cylinder ends) and (2) 3182249 ( non cylinder) using (4) new bolts 3182279, applying loctite to threads and torque to 40-45 ft/lbs.6. Reposistion table top air cylinder between clamp carriers and assemble (2) 1/2-13 hex nuts (from step 3) tighten snug then loosen 1/2 turn. CYLINDER MUST BE FREE TO MOVE!7. Remove and discard tee fitting from spider and replace close nipple 3182366, and cross fitting 3182367 (2 places) using pipe sealing compound on all threads.8. Install (2) straight fittings 3181999 one to each side of cross fitting and (1) 90 elbow fitting 3181998 in each cross fitting.9.

Install (6) 3/8 X 12 1/4 nylon tubes 3182036 (4) between spider and inflation nozzels, and (2) between spider and clamp carriers.10. Reconnect air supply and activate clamp pedal chacking for air leaks. NOTE IF ANY AIR LEAKS ARE DETECTED DISCONNECT AIR SUPPLY BEFORE CORRECTING! After making any necessary corrections, reconnect air supply and recheck for any air leaks. If unit is electric model reconnect power supply.Parts List:QTYPT#DESCRIPTIONQTYPT#DESCRIPTION23182248clamp carrier cyl.

Fitting 1/4' npt23182249clamp carrier231823661/4' close nipple43113325rim clamp adj.43182250pludger and spring43182279adj. Clamp link bolt631820363/8 x 12 1/2' tube male elbow23182367cross fitting.